“The foundation of your home is built up by the walls. The weather out there will not be nice and you need to pay special attention to the exterior walls of your house. It’s not enough to paint a wall. After dealing with rain, snow, wind, dust, and the heat of the outside environment, the paint will begin to peel off.”

Thus, waterproofing is the best way to ensure that your walls are protected and retain your house’s longevity. At the same time, it is vital to reduce your frequent renovation cost. So, here are some of the simple steps for providing effective waterproofing solutions to your home.

Damp carpets and beneath wall coverings can be the most prominent place for mold and mildew growth. Finishing a basement without first dealing with the moisture problems can make health conditions worse and lead to significant damage. Interior waterproofing systems, installed by a professional contractor, can keep the moisture away throughout the home.

Step 1: Properly expose the outside part of the wall

To start with waterproofing your exterior walls, make sure it is properly exposed to work on. Your house walls possess a lot of dirt, which creates an additional layer over the wall. Get rid of all the filth and dust from the walls. And before doing so, remove all the drainage pipes and the old field tiles to get proper access to every corner and area of the wall.

Step 2: Thoroughly clean the walls

Dust and dirt are carried by air and stick to the outer part of the wall. To make the process efficient, you need to clear the debris and dust thoroughly. The dirt and debris can be cleaned with a broom, brush or scraper. Then use a power washer to clean it all off.

Step 3: Check out for the cracks and fill them up

Cracks and holes can be found over time on your exterior walls. Follow up the cleaning process with a thorough look at the cracks and holes on the wall to make sure proper weatherproofing is ensured. They should be filled up with cement.

Most of the homeowners get worried about cracks in the foundation. But the fact is, not all foundation cracks affect the home’s structural integrity. Sometimes cracks can be caused by shrinkage during the concrete curing process. These unsightly, non-structural shrinkages, commonly known as hairline cracks, don’t put your home in immediate danger. But on the other hand, structural cracks are serious business.

All over the internet and TV you find websites and programs with step-by-step guides of DIY foundation repair. But the truth is that a foundation should not be experimented on in a DIY project. Foundation repair requires years of experience and specialized tools. When it comes to foundation repair, contact a foundation repair expert.

The mixture of cement penetrated inside the cracks. Make sure to remove the loose cement from the wall before you apply the cement.

Step 4: Add a layer of cement waterproofing sealer

If you want to make your wall waterproof, you need to apply the cement waterproofer. After applying the cement in the crevices of the walls, let it dry and then apply the waterproof paint seal. Allow it to become dry after that.

Step 5: Pick the right water-proofer

There are many products in the market. You need to pick the right one for your wall. Pick the water-proofer based on whether it is a concrete wall or a silicate-based one.

A silicate-based concrete sealer is one of the options you can choose from. Pick a plaster waterproof Additive to strengthen your walls.

Step 6: Apply the water-proofer

The water-proofer should be applied with a roller or brush. Give a thin coat if you want to apply more than one layer. Allow the first coating to dry and then add the second one.

Step 7: Apply tar and heavy-duty membrane

“If you want to add more strength to the layer, you need to use a tar-based pitch after you’ve dried the cement. It should be applied on your wall.”

After that, you need to apply a heavy-duty plastic or rubber membrane, which will ensure the proper care of your walls.

Step 8: Consider adding gravel

The base for the trench should be below the footer. The drainage pipes will get adequate support from a 34-inches gravel base. Gravel is long lasting and provides enhanced protection.

You have to lay the drainage pipe-cover along with the gravel. Go near the footer and level the gravel. The pipe needs to be covered for at least 3 inches.

Step 9: Add a fabric barrier

A fabric barrier is needed to secure the pipe. Ensuring a fabric barrier is going to keep your system clean. Then build the top of the dirt relatively high and let it settle for some time. Slope the ground away from the walls for the run-off after youTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkiaTrademarkia isTrademarkiaTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia


Good waterproof gives your home a new life and strength to deal with weather-related issues. Magicrete can help you find good solutions for your walls. At a very low and affordable price, Magicrete can provide you with proper weatherproofing.

“It’s not like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like”

Leave a Reply

Your email address will not be published. Required fields are marked *